-
1 Gleichgewichtszone des Bodens
зона предельного равновесия грунта
Зона грунтовой толщи под фундаментом сооружения, во всех точках которой сдвигающие напряжения равны предельному сопротивлению грунта сдвигу
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Gleichgewichtszone des Bodens
-
2 Méthode der Berechnung nach Grenzzuständen
метод расчёта по предельным состояниям
Метод расчёта конструкций и оснований сооружений, в основу которого положен принцип недопустимости перехода рассчитываемого объекта в какое-либо предельное состояние в период строительства и последующей эксплуатации
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Méthode der Berechnung nach Grenzzuständen
-
3 Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Dauerstrombelastbarkeit, f
-
4 Strombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Strombelastbarkeit, f
-
5 thermisches Gleichgewicht
тепловое равновесие
-
[IEV number 151-16-33]EN
thermal equilibrium
state reached when the temperature of the parts of a component or equipment operating in a given environment no longer varies faster than a specified limit
[IEV number 151-16-33]FR
équilibre thermique, m
état atteint lorsque la température des parties d’un composant ou d’un matériel fonctionnant dans un environnement déterminé a cessé de varier plus vite qu’une limite spécifiée
[IEV number 151-16-33]EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > thermisches Gleichgewicht
-
6 Schutzimpedanz, f
устройство защитного сопротивления
Компонент или совокупность компонентов, полное сопротивление и конструкция которого(ых) предназначены для ограничения установившегося тока прикосновения и электрического разряда до неопасного уровня.
[ ГОСТ Р МЭК 60050-826-2009]EN
protective impedance device
component or assembly of components whose impedance and construction are intended to limit steady-state touch current and electric charge to non-hazardous levels
[IEV number 826-12-35]FR
impédance de protection, f
composant ou ensemble de composants dont l'impédance et la conception sont telles qu'elles assurent la limitation du courant de contact en régime établi et de la charge électrique à des niveaux non dangereux
[IEV number 826-12-35]Тематики
EN
DE
- Schutzimpedanz, f
FR
- impédance de protection, f
Немецко-русский словарь нормативно-технической терминологии > Schutzimpedanz, f
См. также в других словарях:
Limit state design — (LSD) refers to a design methodology used in structural engineering. The methodology is in fact a modernization and rationalization of engineering knowledge which was well established prior to the adoption of LSD. Beyond the concept of a limit… … Wikipedia
State Scenic Highway System (California) — infobox road state=CA marker highway name=State Scenic Highway SystemThe State Scenic Highway System is a list of highways, mainly state highways, that have been designated by the California Department of Transportation (Caltrans) as scenic… … Wikipedia
limit# — limit n Limit, bound, confine, end, term are comparable when they mean an actual or imaginary line beyond which a thing does not or cannot extend. Limit is the most inclusive of these terms because it carries no necessary implication of number,… … New Dictionary of Synonyms
Limit loads — Limit load is the maximum load that a structure can safely carry. It s the load at which the structure is in a state of incipient plastic collapse. As the load on the structure increases, the displacements increases linearly in the elastic range… … Wikipedia
state second pension — (S2P) A top up state pension that replaced the state earnings related pension scheme (SERPS) from 6 April 2002. S2P is an additional state pension based on an employee s national insurance contributions (NICs … Law dictionary
State College Area School District — We are the future! Type and location Type Public Country United States … Wikipedia
State highway — State highway, state road or state route can refer to one of three related concepts, two of them related to a state government in a country that is divided into states (including the United States, Australia and Mexico): #A road numbered by the… … Wikipedia
State Sponsors of Terrorism — is a designation applied by the United States Department of State to nations who are designated by the Secretary of State to have repeatedly provided support for acts of international terrorism. [http://www.state.gov/s/ct/c14151.htm] Inclusion on … Wikipedia
State income tax — is an income tax in the United States that is levied by each individual state. Seven states choose to impose no income tax. These states are Alaska, Florida, Nevada, South Dakota, Texas, Washington, and Wyoming. Additionally, New Hampshire and… … Wikipedia
State and Local Affairs — ▪ 1997 Introduction States continued to be at the centre of national debates on public policy during 1996. The U.S. Congress, reacting in part to successful experimentation by a number of states, enacted a historic welfare reform measure… … Universalium
Limit (category theory) — In category theory, a branch of mathematics, the abstract notion of a limit captures the essential properties of universal constructions such as products and inverse limits. The dual notion of a colimit generalizes constructions such as disjoint… … Wikipedia
